行业资讯

当前位置:网站17彩票 > 新闻中心 > 行业资讯

  • 使用金属清洗剂的几个要点
  • 本站编辑:杭州洛克威化工17彩票发布日期:2019-04-07 18:47 浏览次数:
清洗剂作为一种新型工业清洗剂,它可以代替汽油、柴油或 煤油清洗金属设备及零件,它节油、安全、成本低、清洁卫生、清洗 质量好、效果佳等。
 
 
 
使用金属清洗剂的几个要点
 
1. 配制好适当的浓度。金属清洗剂的效果与清洗液的浓度有关, 但浓度增加到一定值时, 超声波清洗机性能不会再有明显改善。 不同的零件应配制不同浓度的清洗液。 清洗一般零件, 浓度以 2%~3%为宜;清洗重垢零件,浓度以 5%为宜;清洗后桥齿轮及轴类零件,浓 度以 3%~4%为佳。
 
2. 控制和掌握好温度。在一定的温度范围内,金属清洗剂有利于 油垢及油脂的溶解。 因此, 克林沃尔认为应严格按各种金属清洗剂所规 定的适宜温度范围进行清洗。 夏季清洗一般零件可在常温下进行, 春 秋季节应适当加热或用温开水配制清洗液, 冬季一定要加热乙清洗重 垢零件时, 温度应适当提高。加热可采取浸煮或直接加热水等方法, 根据具体情况而定。
 
3. 掌握正确的清洗方法。清洗液配好后,应用两个清洗容器分别 进行粗洗和精洗。清洗前,对表面污垢厚、积炭多的零件先进行刮、 擦,然后浸在粗洗容器中浸泡一定时间,再由粗洗到精洗。清洗时应 先清洗精密零件,然后再清洗一般零件。清洗曲轴等零件的水道、油道时, 用压力枪或其它喷射工具进行加压冲洗效果更好。 清洗一定时间后,应将精洗容器内的清洗液倒入粗洗容器内,然后再换上干净的清洗 液,以保证精洗质量。使用时还应检查 pH 值,若 pH 值小于 7,则 应补充清洗剂,以保证清洗质量。
 
4. 不使用失效的清洗剂。购买和使用时要注意有效期,不使用失效的清洗剂。金属清洗剂应定量配制,并尽量现用现配。报废后的清 洗液若数量较少,对环境污染甚微;若数量较多时,会污染环境,需进行废液处理。清洗后的农机零件应擦干或晾干后再使用。



As a new type of industrial cleaning agent, cleaning agent can replace gasoline, diesel or kerosene to clean metal equipment and parts. It saves oil, safety, low cost, cleanliness, good cleaning quality and good effect.
A few points about using a metal cleaner
1。 Set the right concentration。 The effect of metal cleaning agent is related to the concentration of cleaning liquid, but when the concentration increases to a certain value, the performance of ultrasonic cleaning machine will not improve significantly。 Different parts should be prepared with different concentrations of cleaning fluid。 Wash general parts, the concentration of 2 % ~ 3 % is appropriate; Cleaning heavy scale parts, the concentration of 5 % is appropriate; Wash back bridge gear and shaft parts, concentration 3 % ~ 4 % is better。
2. Control and control the temperature. In a certain temperature range, the metal cleaning agent is conducive to the dissolution of grease and grease. Therefore, Kelinwoer believes that cleaning should be strictly in accordance with the appropriate temperature range defined by various metal cleaning agents. Summer cleaning general parts can be carried out at room temperature, spring and autumn season should be properly heated or prepared with warm water cleaning solution, winter must be heated B cleaning heavy scale parts, the temperature should be appropriately raised. Heating can be done by soaking or directly adding hot water, depending on the specific situation.
3. Master the proper cleaning methods. After the cleaning liquid is prepared, two cleaning containers shall be used for rough washing and fine washing respectively. Before cleaning, the surface dirt thick, more carbon parts first scratch, wipe, and then immerse in a rough washing container for a certain period of time, and then wash from rough to fine. Wash the precision parts first, and then clean the general parts. Use pressure gun or other injection tool to wash water channel and oil channel of crankshaft and other parts. After cleaning for a certain period of time, the cleaning liquid in the washing container should be poured into the coarse washing container, and then replaced with a clean cleaning liquid to ensure the quality of the washing. The pH should also be checked during use, and if the pH is less than 7, the cleaning agent should be added to ensure the cleaning quality.
4. Do not use invalid cleaning agent. When purchasing and using, pay attention to the validity period and do not use invalid cleaning agents. The metal cleaning agent should be prepared quantitatively and present as far as possible. If the amount of cleaning liquid after scrapping is small, there is little environmental pollution. If the quantity is large, it will pollute the environment and need to be treated with waste liquid. After cleaning, the parts of the farm machine should be dried or dried before use.
满堂彩注册 江苏快3网 河北快3走势图 178彩票 大信彩票投注 139彩票 河北快3 河北快3走势图 头彩网 265彩票